打印
M-219 Feet Sensor

Response time: ≤ 45ms  relay output monitor signal: 4.5mA   Power Input :12-36V AC / DC

 

Power consumption: 82mA    detection mode: Foot often appear, the light beams are cut eye                     Size: 149 (length) * 13 (diameter) mm

 

Dimensions: 186 (length) * 175 (W) * 60 (D) mm                                            Main body in shape size: 118 (length) * 100 (W) * 54 (D) mm (hole)

Details

Widely used in hospital operating rooms, laboratories, and the clean room entrance automatic door sensor control, easy to operate, instead of their feet, to eliminate hand contact ,say no contamination.
Response time: ≤ 45ms  relay output monitor signal: 4.5mA   Power Input :12-36V AC / DC
Power consumption: 82mA    detection mode: Foot often appear, the light beams are cut eye                     Size: 149 (length) * 13 (diameter) mm
Dimensions: 186 (length) * 175 (W) * 60 (D) mm                                            Main body in shape size: 118 (length) * 100 (W) * 54 (D) mm (hole)

Microprocessor modulation and demodulation active active infrared. Microcomputer control, international refined brushed stainless steel exterior design. Easy installation, stable performance,stronge anti-interference  ability. Optional single group with the controller, can also choose both inside and outside a group (dual).

 

 

Widely used in hospital operating rooms, laboratories, and the clean room entrance automatic door sensor control, easy to operate, instead of their feet, to eliminate hand contact ,say no contamination.

 

Response time: ≤ 45ms  relay output monitor signal: 4.5mA   Power Input :12-36V AC / DC

 

Power consumption: 82mA    detection mode: Foot often appear, the light beams are cut eye                     Size: 149 (length) * 13 (diameter) mm

 

Dimensions: 186 (length) * 175 (W) * 60 (D) mm                                            Main body in shape size: 118 (length) * 100 (W) * 54 (D) mm (hole)

 

Microprocessor modulation and demodulation active active infrared. Microcomputer control, international refined brushed stainless steel exterior design. Easy installation, stable performance,stronge anti-interference  ability. Optional single group with the controller, can also choose both inside and outside a group (dual).

 
 
 
 

Operational Guidelines

M-219    Feet Sensor Kits


1.security Guide

Thanks for purchasing this product, in order to use the product properly ,please read this operations guide before using.

 

The overall characteristic

Microcomputer control, internationalization exquisite shape design of stainless steel wire drawing.

Concealed fixation screws on the front, small embedded fine eye for light and . easy installation, stable performance, strong anti-inter ference.

Used in hospital operating rooms, laboratories and clean room entrance and automatic door sensor control.

Modulation of the active microprocessor active infrared.

Detection mode :the feet instead of the hand, beam is truncated and output a signal to open door when it is touched.

 

Dimensions and panel layout

 

 

Device composed

 

1Two shielded wires(Standard 5.5 m)                   2 A master controller       

3Pairs of laser beam pull-type cylindrical.               4Stainless steel assemblies(one or two)

5.The terminal wiring of input and output

 

 

Notes: When using a single group, this DIP switch must be allocated .When using dual group, this DIP switch must be on the dial. Otherwise, it will lead to not work Properly.

Select the extended leg sensor sensitivity: Under the pull: Sensor sensitivity turn out to be weak Up the pull: 6.Sensor sensitivity turn out to be strong.

The main technology parametric

Technical measures: Micro modulation and demodulation of active a ctive infrared

Recommended installation height: Center 0.3 m from the ground

Half-angle of beam deviation:

Detection mode: the feet instead of the hand, beam is truncated and output a signal

 to open door when it is touched.

Reaction time: relay output 45ms

Supply power: AC/DC 12~36V

Total power consumption: 82mA

Monitor signal: 4.5S MA

Signal direction: Effective control on the radio, the red light is lit, the green light flashes .

when the beam is truncated.

Environment temperature: -20¡æ~+55¡æ

Immunity: Sunlight 81000LUX

Grilled white light: 36000LUX

Electronic Microwave: Consistent with 89/336/CEE criteria

Appearance dimensions ; 123(L)x50(W)x32(H)mm  (Main controller)

19mmx13mm(Light eyes )

186mmx175mmX53mm(Main shell)

Output signal: relay output by the passive cable contact

M-219   Feet sensor  switch